CVE-2026-80653
HighCVSS 8.4Exploitation Probability (EPSS)
Low risk4th percentile - higher than 4% of all known CVEs
Summary
In the Linux kernel, the scsi: hisi_sas driver lacked a slave_destroy interface, causing warnings during simultaneous link reset and module removal. The fix adds this interface to ensure proper link removal after workqueues are flushed.
Risk Assessment
Risk of system instability and kernel warnings during SAS operations, potentially affecting availability.
Recommendation
Apply the Linux kernel update containing the fix for the hisi_sas driver.
Other vulnerabilities in Linux kernel
See all- CVE-2026-80577Unknown
In the Linux kernel's drm/panthor driver, panthor_fw_load_section_entry() skips BO creation for zero-sized firmware sections but adds them to the section list, leading to NULL pointer dereference in later paths. The fix skips adding such sections to the list.
- CVE-2026-80571Unknown
In the Linux kernel powerpc/pseries papr-phy-attest, missing validation of cmd.length could lead to buffer overflow. The fix adds length checks and fixes memory leaks on error paths.
- CVE-2026-80567Unknown
In the Linux kernel Synaptics RMI4 driver (F54), worker errors were not propagated to the V4L2 queue, causing stale or uninitialized data to be delivered to userspace. The fix adds error checking and marks buffers as error state.
- CVE-2026-80566Unknown
In the Linux kernel, the hynitron_cstxxx driver improperly validated touch count and finger IDs. This can lead to corrupted touch state or out-of-bounds buffer access.
- CVE-2026-80564Unknown
In the Linux kernel, the gve driver lacks an implementation of adjfine, leading to a NULL pointer dereference when triggered from userspace, e.g., via testptp.
- CVE-2026-80563Unknown
A use-after-free vulnerability was found in the Linux kernel's gpio-sloppy-logic-analyzer driver. The 'trigger' debugfs file lacked proper protection, allowing a write to freed memory during device unbind. The issue was fixed by using debugfs_create_file() instead of debugfs_create_file_unsafe().
- CVE-2026-80543Unknown
In the Linux kernel, the xcrb_msg_to_type6cprb_msgx() and xcrb_msg_to_type6_ep11cprb_msgx() functions for s390/zcrypt copy a user space message into a kernel buffer based on length, but further processing assumes 4-byte alignment. As a result, up to 3 bytes of uninitialized kernel memory are forwarded to further processing, potentially exposing kernel memory to the crypto card firmware.
- CVE-2026-80542Unknown
In the Linux kernel, the amdgpu driver for AMD Display has a NULL pointer dereference in amdgpu_dm_crtc_set_vblank() when vblank is enabled or queried before a stream is attached to acrtc_state->stream. This can lead to a system crash.
- CVE-2026-80535Unknown
In the Linux kernel XFS filesystem, during directory tree repair, a self-referential directory may be detected. In such a case, the repair code attempts to lock the same inode twice (double iolock/ilock), leading to a deadlock. The fix detects this corner case and handles it appropriately.
- CVE-2026-80533Unknown
In the Linux kernel XFS filesystem, during AGI repair, the function xrep_iunlink_walk_ondisk_bucket may attempt to use the pointer sc->sa.agi_bp, which can be null if the buffer verifier fails. The fix uses ragi->agi_bp instead, which skips verifier checks, to avoid walking off the end of memory.
Original NVD description (English source)
In the Linux kernel, the following vulnerability has been resolved: scsi: hisi_sas: Add slave_destroy interface for v3 hw WARNING is triggered when executing link reset of remote PHY and rmmod SAS driver simultaneously. Following is the WARNING log: WARNING: CPU: 61 PID: 21818 at drivers/base/core.c:1347 __device_links_no_driver+0xb4/0xc0 Call trace: __device_links_no_driver+0xb4/0xc0 device_links_driver_cleanup+0xb0/0xfc __device_release_driver+0x198/0x23c device_release_driver+0x38/0x50 bus_remove_device+0x130/0x140 device_del+0x184/0x434 __scsi_remove_device+0x118/0x150 scsi_remove_target+0x1bc/0x240 sas_rphy_remove+0x90/0x94 sas_rphy_delete+0x24/0x3c sas_destruct_devices+0x64/0xa0 [libsas] sas_revalidate_domain+0xe4/0x150 [libsas] process_one_work+0x1e0/0x46c worker_thread+0x15c/0x464 kthread+0x160/0x170 ret_from_fork+0x10/0x20 ---[ end trace 71e059eb58f85d4a ]--- During SAS phy up, link->status is set to DL_STATE_AVAILABLE in device_links_driver_bound, then this setting influences __device_links_no_driver() before driver rmmod and caused WARNING. Add the slave_destroy interface to make sure link is removed after flush workque.

