CVE-2026-74661
HighCVSS 7.8Exploitation Probability (EPSS)
Low risk2th percentile - higher than 2% of all known CVEs
Summary
In the Linux kernel mac802154 subsystem, the beacon worker reads local->beacon_req under RCU but continues to use sdata and wpan_dev after leaving the RCU section. This can lead to use-after-free after interface teardown.
Risk Assessment
This vulnerability could cause a system crash or potential privilege escalation due to use-after-free.
Recommendation
Apply the kernel patch that takes a netdev reference before leaving the RCU section in the beacon worker.
Other vulnerabilities in Linux kernel
See all- CVE-2026-80577Unknown
In the Linux kernel's drm/panthor driver, panthor_fw_load_section_entry() skips BO creation for zero-sized firmware sections but adds them to the section list, leading to NULL pointer dereference in later paths. The fix skips adding such sections to the list.
- CVE-2026-80571Unknown
In the Linux kernel powerpc/pseries papr-phy-attest, missing validation of cmd.length could lead to buffer overflow. The fix adds length checks and fixes memory leaks on error paths.
- CVE-2026-80567Unknown
In the Linux kernel Synaptics RMI4 driver (F54), worker errors were not propagated to the V4L2 queue, causing stale or uninitialized data to be delivered to userspace. The fix adds error checking and marks buffers as error state.
- CVE-2026-80566Unknown
In the Linux kernel, the hynitron_cstxxx driver improperly validated touch count and finger IDs. This can lead to corrupted touch state or out-of-bounds buffer access.
- CVE-2026-80564Unknown
In the Linux kernel, the gve driver lacks an implementation of adjfine, leading to a NULL pointer dereference when triggered from userspace, e.g., via testptp.
- CVE-2026-80563Unknown
A use-after-free vulnerability was found in the Linux kernel's gpio-sloppy-logic-analyzer driver. The 'trigger' debugfs file lacked proper protection, allowing a write to freed memory during device unbind. The issue was fixed by using debugfs_create_file() instead of debugfs_create_file_unsafe().
- CVE-2026-80543Unknown
In the Linux kernel, the xcrb_msg_to_type6cprb_msgx() and xcrb_msg_to_type6_ep11cprb_msgx() functions for s390/zcrypt copy a user space message into a kernel buffer based on length, but further processing assumes 4-byte alignment. As a result, up to 3 bytes of uninitialized kernel memory are forwarded to further processing, potentially exposing kernel memory to the crypto card firmware.
- CVE-2026-80542Unknown
In the Linux kernel, the amdgpu driver for AMD Display has a NULL pointer dereference in amdgpu_dm_crtc_set_vblank() when vblank is enabled or queried before a stream is attached to acrtc_state->stream. This can lead to a system crash.
- CVE-2026-80535Unknown
In the Linux kernel XFS filesystem, during directory tree repair, a self-referential directory may be detected. In such a case, the repair code attempts to lock the same inode twice (double iolock/ilock), leading to a deadlock. The fix detects this corner case and handles it appropriately.
- CVE-2026-80533Unknown
In the Linux kernel XFS filesystem, during AGI repair, the function xrep_iunlink_walk_ondisk_bucket may attempt to use the pointer sc->sa.agi_bp, which can be null if the buffer verifier fails. The fix uses ragi->agi_bp instead, which skips verifier checks, to avoid walking off the end of memory.
Original NVD description (English source)
In the Linux kernel, the following vulnerability has been resolved: mac802154: fix netdev use-after-free in beacon worker mac802154_beacon_worker() reads local->beacon_req under RCU and derives the sub-interface from the request, but then drops the RCU read lock and continues to use both sdata and the embedded wpan_dev. mac802154_stop_beacons_locked() cancels only pending beacon work, clears local->beacon_req and frees the request. A beacon worker that is already running can therefore continue after interface teardown and dereference the freed netdev private area. The scan worker already pins the netdev before leaving RCU. Apply the same lifetime rule to the beacon worker: take a netdev reference while the request is still protected by RCU, and release it on all paths that continue after the reference is acquired.

