CVE-2026-72016
Low risk· EPSS 10%Exploitation Probability (EPSS)
Low risk10th percentile - higher than 10% of all known CVEs
Summary
A vulnerability in the Linux kernel's cpuhp_smt_enable() function causes a NULL kobject warning when calling sysfs_create_group(). The issue occurs on arm64 when booting with maxcpus greater than the number of physically present CPUs, where CPUs marked as 'present' are not yet registered. The fix involves checking the ACPI_MADT_ENABLED flag before setting a CPU as present and properly managing the present mask in acpi_map_cpu() and acpi_unmap_cpu().
Risk Assessment
The vulnerability may lead to incorrect SMT hotplug behavior, causing configuration errors, system warnings, and potential instability in virtualized environments. Organizations using arm64 with dynamic CPU addition may face resource management issues.
Recommendation
Apply the official Linux kernel patch addressing CVE-2026-72016 immediately. Update to a kernel version containing the fix and verify ACPI/MADT configuration in virtualized environments.
Other vulnerabilities in Linux kernel
See all- CVE-2026-80577Unknown
In the Linux kernel's drm/panthor driver, panthor_fw_load_section_entry() skips BO creation for zero-sized firmware sections but adds them to the section list, leading to NULL pointer dereference in later paths. The fix skips adding such sections to the list.
- CVE-2026-80571Unknown
In the Linux kernel powerpc/pseries papr-phy-attest, missing validation of cmd.length could lead to buffer overflow. The fix adds length checks and fixes memory leaks on error paths.
- CVE-2026-80567Unknown
In the Linux kernel Synaptics RMI4 driver (F54), worker errors were not propagated to the V4L2 queue, causing stale or uninitialized data to be delivered to userspace. The fix adds error checking and marks buffers as error state.
- CVE-2026-80566Unknown
In the Linux kernel, the hynitron_cstxxx driver improperly validated touch count and finger IDs. This can lead to corrupted touch state or out-of-bounds buffer access.
- CVE-2026-80564Unknown
In the Linux kernel, the gve driver lacks an implementation of adjfine, leading to a NULL pointer dereference when triggered from userspace, e.g., via testptp.
- CVE-2026-80563Unknown
A use-after-free vulnerability was found in the Linux kernel's gpio-sloppy-logic-analyzer driver. The 'trigger' debugfs file lacked proper protection, allowing a write to freed memory during device unbind. The issue was fixed by using debugfs_create_file() instead of debugfs_create_file_unsafe().
- CVE-2026-80543Unknown
In the Linux kernel, the xcrb_msg_to_type6cprb_msgx() and xcrb_msg_to_type6_ep11cprb_msgx() functions for s390/zcrypt copy a user space message into a kernel buffer based on length, but further processing assumes 4-byte alignment. As a result, up to 3 bytes of uninitialized kernel memory are forwarded to further processing, potentially exposing kernel memory to the crypto card firmware.
- CVE-2026-80542Unknown
In the Linux kernel, the amdgpu driver for AMD Display has a NULL pointer dereference in amdgpu_dm_crtc_set_vblank() when vblank is enabled or queried before a stream is attached to acrtc_state->stream. This can lead to a system crash.
- CVE-2026-80535Unknown
In the Linux kernel XFS filesystem, during directory tree repair, a self-referential directory may be detected. In such a case, the repair code attempts to lock the same inode twice (double iolock/ilock), leading to a deadlock. The fix detects this corner case and handles it appropriately.
- CVE-2026-80533Unknown
In the Linux kernel XFS filesystem, during AGI repair, the function xrep_iunlink_walk_ondisk_bucket may attempt to use the pointer sc->sa.agi_bp, which can be null if the buffer verifier fails. The fix uses ragi->agi_bp instead, which skips verifier checks, to avoid walking off the end of memory.
Original NVD description (English source)
In the Linux kernel, the following vulnerability has been resolved: cpu/hotplug: Fix NULL kobject warning in cpuhp_smt_enable() On arm64, when booting with `maxcpus` greater than the number of present CPUs (e.g., QEMU -smp cpus=4,maxcpus=8), some CPUs are marked as 'present' but have not yet been registered via register_cpu(). Consequently, the per-cpu device objects for these CPUs are not yet initialized. In cpuhp_smt_enable(), the code iterates over all present CPUs. Calling _cpu_up() for these unregistered CPUs eventually leads to sysfs_create_group() being called with a NULL kobject (or a kobject without a directory), triggering the following warning in fs/sysfs/group.c: WARNING: fs/sysfs/group.c:137 at internal_create_group+0x41c/0x4bc, CPU#2: sh/181 [...] Call trace: internal_create_group+0x41c/0x4bc (P) sysfs_create_group+0x18/0x24 topology_add_dev+0x1c/0x28 cpuhp_invoke_callback+0x104/0x20c __cpuhp_invoke_callback_range+0x94/0x11c _cpu_up+0x200/0x37c When booting with ACPI, arm64 smp_prepare_cpus() currently sets all enumerated CPUs as "present" regardless of their status in the MADT. This causes issues with SMT hotplug control. For instance, with QEMU's "-smp 4,maxcpus=8" configuration, the MADT GICC entries are populated as follows: 1. The first four CPUs: `Enabled` set but `Online Capable` not set. 2. The remaining four CPUs: `Online Capable` set but `Enabled` not set to support potential hot-plugging. Fix this by: 1. When booting with ACPI, checking the ACPI_MADT_ENABLED flag in the GICC entry before calling set_cpu_present() during SMP initialization. 2. Properly managing the present mask in acpi_map_cpu() and acpi_unmap_cpu() to support actual CPU hotplug events, This aligns with other architectures like x86 and LoongArch. 3. Update the arm64 CPU hotplug documentation to no longer state that all online-capable vCPUs are marked as present by the kernel at boot time. This ensures that only physically available or explicitly enabled CPUs are in the present mask, keeping the SMT control logic consistent with the actual hardware state.

