CVE-2026-68469
Low risk· EPSS 12%Exploitation Probability (EPSS)
Low risk12th percentile - higher than 12% of all known CVEs
Summary
In the Linux kernel, the mwifiex driver has a vulnerability causing permanently busy Wi-Fi scans after multiple roam iterations. The issue stems from incorrect power-save state (ps_state) handling during association response processing, leading to a missing sleep confirmation and blocking subsequent scans.
Risk Assessment
An attacker or roaming failure can cause a permanent inability to scan Wi-Fi networks, preventing network switching and potentially causing connectivity disruptions for users.
Recommendation
Apply a Linux kernel update containing the fix that removes the incorrect ps_state assignment in mwifiex_ret_802_11_associate(). If possible, limit use of devices with IW412 chipsets until the patch is deployed.
Other vulnerabilities in Linux kernel
See all- CVE-2026-80577Unknown
In the Linux kernel's drm/panthor driver, panthor_fw_load_section_entry() skips BO creation for zero-sized firmware sections but adds them to the section list, leading to NULL pointer dereference in later paths. The fix skips adding such sections to the list.
- CVE-2026-80571Unknown
In the Linux kernel powerpc/pseries papr-phy-attest, missing validation of cmd.length could lead to buffer overflow. The fix adds length checks and fixes memory leaks on error paths.
- CVE-2026-80567Unknown
In the Linux kernel Synaptics RMI4 driver (F54), worker errors were not propagated to the V4L2 queue, causing stale or uninitialized data to be delivered to userspace. The fix adds error checking and marks buffers as error state.
- CVE-2026-80566Unknown
In the Linux kernel, the hynitron_cstxxx driver improperly validated touch count and finger IDs. This can lead to corrupted touch state or out-of-bounds buffer access.
- CVE-2026-80564Unknown
In the Linux kernel, the gve driver lacks an implementation of adjfine, leading to a NULL pointer dereference when triggered from userspace, e.g., via testptp.
- CVE-2026-80563Unknown
A use-after-free vulnerability was found in the Linux kernel's gpio-sloppy-logic-analyzer driver. The 'trigger' debugfs file lacked proper protection, allowing a write to freed memory during device unbind. The issue was fixed by using debugfs_create_file() instead of debugfs_create_file_unsafe().
- CVE-2026-80543Unknown
In the Linux kernel, the xcrb_msg_to_type6cprb_msgx() and xcrb_msg_to_type6_ep11cprb_msgx() functions for s390/zcrypt copy a user space message into a kernel buffer based on length, but further processing assumes 4-byte alignment. As a result, up to 3 bytes of uninitialized kernel memory are forwarded to further processing, potentially exposing kernel memory to the crypto card firmware.
- CVE-2026-80542Unknown
In the Linux kernel, the amdgpu driver for AMD Display has a NULL pointer dereference in amdgpu_dm_crtc_set_vblank() when vblank is enabled or queried before a stream is attached to acrtc_state->stream. This can lead to a system crash.
- CVE-2026-80535Unknown
In the Linux kernel XFS filesystem, during directory tree repair, a self-referential directory may be detected. In such a case, the repair code attempts to lock the same inode twice (double iolock/ilock), leading to a deadlock. The fix detects this corner case and handles it appropriately.
- CVE-2026-80533Unknown
In the Linux kernel XFS filesystem, during AGI repair, the function xrep_iunlink_walk_ondisk_bucket may attempt to use the pointer sc->sa.agi_bp, which can be null if the buffer verifier fails. The fix uses ragi->agi_bp instead, which skips verifier checks, to avoid walking off the end of memory.
Original NVD description (English source)
In the Linux kernel, the following vulnerability has been resolved: wifi: mwifiex: fix permanently busy scans after multiple roam iterations In order for the firmware to sleep, the driver has to confirm a previously received sleep request. The normal sequence of evets goes like this: EVENT_SLEEP -> adapter->ps_state = PS_STATE_PRE_SLEEP -> sleep-confirm -> SLEEP -> EVENT_AWAKE -> AWAKE. Before sending the sleep-confirm command, the driver must make sure there are no commands either running or waiting to be completed. mwifiex_ret_802_11_associate() unconditionally sets ps_state = PS_STATE_AWAKE when it processes the association command response, outside of the normal powersave management flow. If EVENT_SLEEP arrives while the association command is in flight, ps_state is PRE_SLEEP when the association command response is parsed, and the forced AWAKE overwrites it. The deferred sleep-confirm is never sent. A subsequent scan_start command is correctly acknowledged, but the firmware doesn't generate scan_result events. The scan request never finishes, and additional requests from userspace fail with -EBUSY. After testing on both IW412 and W8997, I could only trigger the bug on the IW412 and observed the firmwares behave differently. On the IW412 the firmware still sends EVENT_SLEEP while the authentication / association process is ongoing. A W8997 under the same conditions seems to suppress power-save for the duration of the association, so PRE_SLEEP never coincided with the association response even after extended periods of testing using the loops described below (>12hours). On the IW412, the delay between commands that triggers an EVENT_SLEEP was empirically determined to be ~20ms. This delay can naturally occur when the driver is outputting debugging information (debug_mask = 0x00000037), in which situation the busy scans issue is repeatable while running "test 1)" as described below. If the delay between commands is less than ~20ms, the firmware stays awake and the issue was not reproducible running the same test. The host_mlme=false path also behaves differently. In this case, the entire authentication / association transaction is executed by one command (HostCmd_CMD_802_11_ASSOCIATE), and the firmware doesn't emit EVENT_SLEEP while the command is running. Remove the assignment so the ps_state is only manipulated in the paths that are related to powersave event handling and on the main workqueue for correct sleep confirmation. The following loop tests were performed (with debugging output enabled): 1) force roaming between two AP's, one 5GHz and one 2.4GHz, same SSID. Use wpa_cli to trigger the roaming behavior, sleep 2s between iterations. 2) force a disconnection to AP 1 and a connection to AP 2, test scan. Use wpa_cli to trigger the connection changes, sleep 2s between iterations. Each test ran in each device for at least 3 hours.