CVE-2026-64409
Low risk· EPSS 7%Exploitation Probability (EPSS)
Low risk7th percentile - higher than 7% of all known CVEs
Summary
In the Linux kernel Bluetooth btmtksdio driver, there is an infinite loop in the btmtksdio_txrx_work() function. The bug is due to incorrect use of time_is_before_jiffies() in the loop condition. After the 5-second timeout expires, the condition becomes always true, causing an infinite loop and locking the SDIO host.
Risk Assessment
An infinite loop can block the Bluetooth driver, preventing the Bluetooth interface from functioning and potentially leading to a system hang.
Recommendation
Apply the Linux kernel patch that fixes the loop termination condition in btmtksdio_txrx_work() to actually enforce the 5-second timeout.
Other vulnerabilities in Linux kernel
See all- CVE-2026-80577Unknown
In the Linux kernel's drm/panthor driver, panthor_fw_load_section_entry() skips BO creation for zero-sized firmware sections but adds them to the section list, leading to NULL pointer dereference in later paths. The fix skips adding such sections to the list.
- CVE-2026-80571Unknown
In the Linux kernel powerpc/pseries papr-phy-attest, missing validation of cmd.length could lead to buffer overflow. The fix adds length checks and fixes memory leaks on error paths.
- CVE-2026-80567Unknown
In the Linux kernel Synaptics RMI4 driver (F54), worker errors were not propagated to the V4L2 queue, causing stale or uninitialized data to be delivered to userspace. The fix adds error checking and marks buffers as error state.
- CVE-2026-80566Unknown
In the Linux kernel, the hynitron_cstxxx driver improperly validated touch count and finger IDs. This can lead to corrupted touch state or out-of-bounds buffer access.
- CVE-2026-80564Unknown
In the Linux kernel, the gve driver lacks an implementation of adjfine, leading to a NULL pointer dereference when triggered from userspace, e.g., via testptp.
- CVE-2026-80563Unknown
A use-after-free vulnerability was found in the Linux kernel's gpio-sloppy-logic-analyzer driver. The 'trigger' debugfs file lacked proper protection, allowing a write to freed memory during device unbind. The issue was fixed by using debugfs_create_file() instead of debugfs_create_file_unsafe().
- CVE-2026-80543Unknown
In the Linux kernel, the xcrb_msg_to_type6cprb_msgx() and xcrb_msg_to_type6_ep11cprb_msgx() functions for s390/zcrypt copy a user space message into a kernel buffer based on length, but further processing assumes 4-byte alignment. As a result, up to 3 bytes of uninitialized kernel memory are forwarded to further processing, potentially exposing kernel memory to the crypto card firmware.
- CVE-2026-80542Unknown
In the Linux kernel, the amdgpu driver for AMD Display has a NULL pointer dereference in amdgpu_dm_crtc_set_vblank() when vblank is enabled or queried before a stream is attached to acrtc_state->stream. This can lead to a system crash.
- CVE-2026-80535Unknown
In the Linux kernel XFS filesystem, during directory tree repair, a self-referential directory may be detected. In such a case, the repair code attempts to lock the same inode twice (double iolock/ilock), leading to a deadlock. The fix detects this corner case and handles it appropriately.
- CVE-2026-80533Unknown
In the Linux kernel XFS filesystem, during AGI repair, the function xrep_iunlink_walk_ondisk_bucket may attempt to use the pointer sc->sa.agi_bp, which can be null if the buffer verifier fails. The fix uses ragi->agi_bp instead, which skips verifier checks, to avoid walking off the end of memory.
Original NVD description (English source)
In the Linux kernel, the following vulnerability has been resolved: Bluetooth: btmtksdio: fix infinite loop in btmtksdio_txrx_work() Every once in a while we see a hung btmtksdio_flush() task: INFO: task kworker/u17:0:189 blocked for more than 122 seconds. __cancel_work_timer+0x3f4/0x460 cancel_work_sync+0x1c/0x2c btmtksdio_flush+0x2c/0x40 hci_dev_open_sync+0x10c4/0x2190 [..] It all boils down to incorrect time_is_before_jiffies() usage in btmtksdio_txrx_work(). The btmtksdio_txrx_work() loop is expected to be terminated if running for longer than 5*HZ. However the timeout check is twisted: time_is_before_jiffies(old_jiffies + 5*HZ) evaluates to true when old_jiffies + 5*HZ is in the past i.e. when a timeout has occurred. Using OR with time_is_before_jiffies(txrx_timeout) means that: - before the 5-second timeout: the condition is `int_status || false`, so it loops as long as there are pending interrupts. - after the 5-second timeout: the condition becomes `int_status || true`, which is always true. When the loop becomes infinite btmtksdio_txrx_work() loop never terminates and never releases the SDIO host. Fix loop termination condition to actually enforce a 5*HZ timeout.

