CVE-2026-64362
Low risk· EPSS 7%Exploitation Probability (EPSS)
Low risk7th percentile - higher than 7% of all known CVEs
Summary
A use-after-free vulnerability was found in the HID driver for Logitech G keyboards (lg-g15). The driver did not cancel pending work before freeing memory, allowing access to freed memory when the device is unplugged.
Risk Assessment
An attacker could exploit this vulnerability for remote code execution or privilege escalation by unplugging the keyboard at the right moment.
Recommendation
Apply the Linux kernel patch that adds a remove callback to cancel work before freeing memory.
Other vulnerabilities in Linux kernel
See all- CVE-2026-80577Unknown
In the Linux kernel's drm/panthor driver, panthor_fw_load_section_entry() skips BO creation for zero-sized firmware sections but adds them to the section list, leading to NULL pointer dereference in later paths. The fix skips adding such sections to the list.
- CVE-2026-80571Unknown
In the Linux kernel powerpc/pseries papr-phy-attest, missing validation of cmd.length could lead to buffer overflow. The fix adds length checks and fixes memory leaks on error paths.
- CVE-2026-80567Unknown
In the Linux kernel Synaptics RMI4 driver (F54), worker errors were not propagated to the V4L2 queue, causing stale or uninitialized data to be delivered to userspace. The fix adds error checking and marks buffers as error state.
- CVE-2026-80566Unknown
In the Linux kernel, the hynitron_cstxxx driver improperly validated touch count and finger IDs. This can lead to corrupted touch state or out-of-bounds buffer access.
- CVE-2026-80564Unknown
In the Linux kernel, the gve driver lacks an implementation of adjfine, leading to a NULL pointer dereference when triggered from userspace, e.g., via testptp.
- CVE-2026-80563Unknown
A use-after-free vulnerability was found in the Linux kernel's gpio-sloppy-logic-analyzer driver. The 'trigger' debugfs file lacked proper protection, allowing a write to freed memory during device unbind. The issue was fixed by using debugfs_create_file() instead of debugfs_create_file_unsafe().
- CVE-2026-80543Unknown
In the Linux kernel, the xcrb_msg_to_type6cprb_msgx() and xcrb_msg_to_type6_ep11cprb_msgx() functions for s390/zcrypt copy a user space message into a kernel buffer based on length, but further processing assumes 4-byte alignment. As a result, up to 3 bytes of uninitialized kernel memory are forwarded to further processing, potentially exposing kernel memory to the crypto card firmware.
- CVE-2026-80542Unknown
In the Linux kernel, the amdgpu driver for AMD Display has a NULL pointer dereference in amdgpu_dm_crtc_set_vblank() when vblank is enabled or queried before a stream is attached to acrtc_state->stream. This can lead to a system crash.
- CVE-2026-80535Unknown
In the Linux kernel XFS filesystem, during directory tree repair, a self-referential directory may be detected. In such a case, the repair code attempts to lock the same inode twice (double iolock/ilock), leading to a deadlock. The fix detects this corner case and handles it appropriately.
- CVE-2026-80533Unknown
In the Linux kernel XFS filesystem, during AGI repair, the function xrep_iunlink_walk_ondisk_bucket may attempt to use the pointer sc->sa.agi_bp, which can be null if the buffer verifier fails. The fix uses ragi->agi_bp instead, which skips verifier checks, to avoid walking off the end of memory.
Original NVD description (English source)
In the Linux kernel, the following vulnerability has been resolved: HID: lg-g15: cancel pending work on remove to fix a use-after-free lg_g15_data is allocated with devm and holds a work item. The report handlers schedule that work straight from device input. lg_g15_event() and lg_g15_v2_event() do it on the backlight cycle key, and lg_g510_leds_event() does it too. The worker dereferences the lg_g15_data back through container_of. The driver had no remove callback and never cancelled the work. So if a report scheduled the work and the keyboard was then unplugged, devres freed lg_g15_data while the work was still pending or running, and the worker touched freed memory. This is a use-after-free. It is reachable as a race on device unplug. Add a remove callback that cancels the work before devres frees the state. g15->work is only initialized for the models that schedule it (G15, G15 v2, G510). The G13 and Z-10 leave it zeroed, so guard the cancel on g15->work.func to avoid cancelling a work that was never set up. The g15 NULL test mirrors the one already in lg_g15_raw_event().