CVE-2026-53308
MediumCVSS 5.5Exploitation Probability (EPSS)
Low risk1th percentile - higher than 1% of all known CVEs
Summary
In the Linux kernel, the max77705 driver leaks memory by not destroying the workqueue on remove() and has a flawed resource release order. Interrupt handlers registered via devm may schedule work on a freed workqueue, leading to use-after-free.
Risk Assessment
The organization risks use-after-free vulnerabilities that could cause system crashes or privilege escalation if an interrupt occurs during the short window after workqueue destruction.
Recommendation
Immediately update the Linux kernel to a version containing the fix (commit using devm for workqueue) or apply the appropriate backport for your distribution.
Other vulnerabilities in Linux kernel
See all- CVE-2026-14367Low
A vulnerability in the I3C IBI subsystem of the Linux kernel (drivers/i3c/i3c_ibi_workq.c) stems from missing synchronization on the free-list of work nodes (sys_slist_t). Allocation and deallocation helpers are called from interrupt context (ISR) and the workqueue thread without locks, leading to a race condition. An attacker with physical access to the I3C bus can trigger a series of interrupts, causing list corruption, double allocation, or out-of-bounds writes.
- CVE-2026-80577Unknown
In the Linux kernel's drm/panthor driver, panthor_fw_load_section_entry() skips BO creation for zero-sized firmware sections but adds them to the section list, leading to NULL pointer dereference in later paths. The fix skips adding such sections to the list.
- CVE-2026-80571Unknown
In the Linux kernel powerpc/pseries papr-phy-attest, missing validation of cmd.length could lead to buffer overflow. The fix adds length checks and fixes memory leaks on error paths.
- CVE-2026-80567Unknown
In the Linux kernel Synaptics RMI4 driver (F54), worker errors were not propagated to the V4L2 queue, causing stale or uninitialized data to be delivered to userspace. The fix adds error checking and marks buffers as error state.
- CVE-2026-80566Unknown
In the Linux kernel, the hynitron_cstxxx driver improperly validated touch count and finger IDs. This can lead to corrupted touch state or out-of-bounds buffer access.
- CVE-2026-80564Unknown
In the Linux kernel, the gve driver lacks an implementation of adjfine, leading to a NULL pointer dereference when triggered from userspace, e.g., via testptp.
- CVE-2026-80563Unknown
A use-after-free vulnerability was found in the Linux kernel's gpio-sloppy-logic-analyzer driver. The 'trigger' debugfs file lacked proper protection, allowing a write to freed memory during device unbind. The issue was fixed by using debugfs_create_file() instead of debugfs_create_file_unsafe().
- CVE-2026-80543Unknown
In the Linux kernel, the xcrb_msg_to_type6cprb_msgx() and xcrb_msg_to_type6_ep11cprb_msgx() functions for s390/zcrypt copy a user space message into a kernel buffer based on length, but further processing assumes 4-byte alignment. As a result, up to 3 bytes of uninitialized kernel memory are forwarded to further processing, potentially exposing kernel memory to the crypto card firmware.
- CVE-2026-80542Unknown
In the Linux kernel, the amdgpu driver for AMD Display has a NULL pointer dereference in amdgpu_dm_crtc_set_vblank() when vblank is enabled or queried before a stream is attached to acrtc_state->stream. This can lead to a system crash.
- CVE-2026-80535Unknown
In the Linux kernel XFS filesystem, during directory tree repair, a self-referential directory may be detected. In such a case, the repair code attempts to lock the same inode twice (double iolock/ilock), leading to a deadlock. The fix detects this corner case and handles it appropriately.
Original NVD description (English source)
In the Linux kernel, the following vulnerability has been resolved: power: supply: max77705: Free allocated workqueue and fix removal order Use devm interface for allocating workqueue to fix two bugs at the same time: 1. Driver leaks the memory on remove(), because the workqueue is not destroyed. 2. Driver allocates workqueue and then registers interrupt handlers with devm interface. This means that probe error paths will not use a reversed order, but first destroy the workqueue and then, via devm release handlers, free the interrupt. The interrupt handler schedules work on this exact workqueue, thus if interrupt is hit in this short time window - after destroying workqueue, but before devm() frees the interrupt - the schedulled work will lead to use of freed memory. Change is not equivalent in the workqueue itself: use non-legacy API which does not set (__WQ_LEGACY | WQ_MEM_RECLAIM). The workqueue is used to update power supply (power_supply_changed()) status, thus there is no point to run it for memory reclaim. Note that dev_name() is not directly used in second argument to prevent possible unlikely parsing any "%" character in device name as format.