CVE-2026-53094
HighCVSS 7.8Exploitation Probability (EPSS)
Low risk3th percentile - higher than 3% of all known CVEs
Summary
In the Linux kernel, a vulnerability in BPF leaves the offload->prog pointer stale after JIT compilation with constant blinding, pointing to a freed program. This causes a page fault when the network namespace is destroyed.
Risk Assessment
An attacker can trigger a kernel panic by running a device-bound BPF program in a network namespace, leading to a denial of service (DoS).
Recommendation
Immediately update the Linux kernel to a version containing the fix (commit updating offload->prog in bpf_jit_prog_release_other()).
Other vulnerabilities in Linux kernel
See all- CVE-2026-14367Low
A vulnerability in the I3C IBI subsystem of the Linux kernel (drivers/i3c/i3c_ibi_workq.c) stems from missing synchronization on the free-list of work nodes (sys_slist_t). Allocation and deallocation helpers are called from interrupt context (ISR) and the workqueue thread without locks, leading to a race condition. An attacker with physical access to the I3C bus can trigger a series of interrupts, causing list corruption, double allocation, or out-of-bounds writes.
- CVE-2026-80577Unknown
In the Linux kernel's drm/panthor driver, panthor_fw_load_section_entry() skips BO creation for zero-sized firmware sections but adds them to the section list, leading to NULL pointer dereference in later paths. The fix skips adding such sections to the list.
- CVE-2026-80571Unknown
In the Linux kernel powerpc/pseries papr-phy-attest, missing validation of cmd.length could lead to buffer overflow. The fix adds length checks and fixes memory leaks on error paths.
- CVE-2026-80567Unknown
In the Linux kernel Synaptics RMI4 driver (F54), worker errors were not propagated to the V4L2 queue, causing stale or uninitialized data to be delivered to userspace. The fix adds error checking and marks buffers as error state.
- CVE-2026-80566Unknown
In the Linux kernel, the hynitron_cstxxx driver improperly validated touch count and finger IDs. This can lead to corrupted touch state or out-of-bounds buffer access.
- CVE-2026-80564Unknown
In the Linux kernel, the gve driver lacks an implementation of adjfine, leading to a NULL pointer dereference when triggered from userspace, e.g., via testptp.
- CVE-2026-80563Unknown
A use-after-free vulnerability was found in the Linux kernel's gpio-sloppy-logic-analyzer driver. The 'trigger' debugfs file lacked proper protection, allowing a write to freed memory during device unbind. The issue was fixed by using debugfs_create_file() instead of debugfs_create_file_unsafe().
- CVE-2026-80543Unknown
In the Linux kernel, the xcrb_msg_to_type6cprb_msgx() and xcrb_msg_to_type6_ep11cprb_msgx() functions for s390/zcrypt copy a user space message into a kernel buffer based on length, but further processing assumes 4-byte alignment. As a result, up to 3 bytes of uninitialized kernel memory are forwarded to further processing, potentially exposing kernel memory to the crypto card firmware.
- CVE-2026-80542Unknown
In the Linux kernel, the amdgpu driver for AMD Display has a NULL pointer dereference in amdgpu_dm_crtc_set_vblank() when vblank is enabled or queried before a stream is attached to acrtc_state->stream. This can lead to a system crash.
- CVE-2026-80535Unknown
In the Linux kernel XFS filesystem, during directory tree repair, a self-referential directory may be detected. In such a case, the repair code attempts to lock the same inode twice (double iolock/ilock), leading to a deadlock. The fix detects this corner case and handles it appropriately.
Original NVD description (English source)
In the Linux kernel, the following vulnerability has been resolved: bpf: Fix stale offload->prog pointer after constant blinding When a dev-bound-only BPF program (BPF_F_XDP_DEV_BOUND_ONLY) undergoes JIT compilation with constant blinding enabled (bpf_jit_harden >= 2), bpf_jit_blind_constants() clones the program. The original prog is then freed in bpf_jit_prog_release_other(), which updates aux->prog to point to the surviving clone, but fails to update offload->prog. This leaves offload->prog pointing to the freed original program. When the network namespace is subsequently destroyed, cleanup_net() triggers bpf_dev_bound_netdev_unregister(), which iterates ondev->progs and calls __bpf_prog_offload_destroy(offload->prog). Accessing the freed prog causes a page fault: BUG: unable to handle page fault for address: ffffc900085f1038 Workqueue: netns cleanup_net RIP: 0010:__bpf_prog_offload_destroy+0xc/0x80 Call Trace: __bpf_offload_dev_netdev_unregister+0x257/0x350 bpf_dev_bound_netdev_unregister+0x4a/0x90 unregister_netdevice_many_notify+0x2a2/0x660 ... cleanup_net+0x21a/0x320 The test sequence that triggers this reliably is: 1. Set net.core.bpf_jit_harden=2 (echo 2 > /proc/sys/net/core/bpf_jit_harden) 2. Run xdp_metadata selftest, which creates a dev-bound-only XDP program on a veth inside a netns (./test_progs -t xdp_metadata) 3. cleanup_net -> page fault in __bpf_prog_offload_destroy Dev-bound-only programs are unique in that they have an offload structure but go through the normal JIT path instead of bpf_prog_offload_compile(). This means they are subject to constant blinding's prog clone-and-replace, while also having offload->prog that must stay in sync. Fix this by updating offload->prog in bpf_jit_prog_release_other(), alongside the existing aux->prog update. Both are back-pointers to the prog that must be kept in sync when the prog is replaced.