CVE-2026-53056
MediumCVSS 5.5Exploitation Probability (EPSS)
Low risk8th percentile - higher than 8% of all known CVEs
Summary
In the Linux kernel, the drm/msm/dpu driver has a mismatch between voltage and frequency during runtime resume. Calling dev_pm_opp_set_rate(dev, 0) drops the MMCX rail to MIN_SVS while the core clock remains at highest frequency, potentially causing instability or system crash.
Risk Assessment
System instability or crash during DPU resume, potentially leading to graphical interface disruptions.
Recommendation
Apply the Linux kernel patch that removes the dev_pm_opp_set_rate(dev, 0) call from dpu_runtime_suspend.
Other vulnerabilities in Linux kernel
See all- CVE-2026-14367Low
A vulnerability in the I3C IBI subsystem of the Linux kernel (drivers/i3c/i3c_ibi_workq.c) stems from missing synchronization on the free-list of work nodes (sys_slist_t). Allocation and deallocation helpers are called from interrupt context (ISR) and the workqueue thread without locks, leading to a race condition. An attacker with physical access to the I3C bus can trigger a series of interrupts, causing list corruption, double allocation, or out-of-bounds writes.
- CVE-2026-80577Unknown
In the Linux kernel's drm/panthor driver, panthor_fw_load_section_entry() skips BO creation for zero-sized firmware sections but adds them to the section list, leading to NULL pointer dereference in later paths. The fix skips adding such sections to the list.
- CVE-2026-80571Unknown
In the Linux kernel powerpc/pseries papr-phy-attest, missing validation of cmd.length could lead to buffer overflow. The fix adds length checks and fixes memory leaks on error paths.
- CVE-2026-80567Unknown
In the Linux kernel Synaptics RMI4 driver (F54), worker errors were not propagated to the V4L2 queue, causing stale or uninitialized data to be delivered to userspace. The fix adds error checking and marks buffers as error state.
- CVE-2026-80566Unknown
In the Linux kernel, the hynitron_cstxxx driver improperly validated touch count and finger IDs. This can lead to corrupted touch state or out-of-bounds buffer access.
- CVE-2026-80564Unknown
In the Linux kernel, the gve driver lacks an implementation of adjfine, leading to a NULL pointer dereference when triggered from userspace, e.g., via testptp.
- CVE-2026-80563Unknown
A use-after-free vulnerability was found in the Linux kernel's gpio-sloppy-logic-analyzer driver. The 'trigger' debugfs file lacked proper protection, allowing a write to freed memory during device unbind. The issue was fixed by using debugfs_create_file() instead of debugfs_create_file_unsafe().
- CVE-2026-80543Unknown
In the Linux kernel, the xcrb_msg_to_type6cprb_msgx() and xcrb_msg_to_type6_ep11cprb_msgx() functions for s390/zcrypt copy a user space message into a kernel buffer based on length, but further processing assumes 4-byte alignment. As a result, up to 3 bytes of uninitialized kernel memory are forwarded to further processing, potentially exposing kernel memory to the crypto card firmware.
- CVE-2026-80542Unknown
In the Linux kernel, the amdgpu driver for AMD Display has a NULL pointer dereference in amdgpu_dm_crtc_set_vblank() when vblank is enabled or queried before a stream is attached to acrtc_state->stream. This can lead to a system crash.
- CVE-2026-80535Unknown
In the Linux kernel XFS filesystem, during directory tree repair, a self-referential directory may be detected. In such a case, the repair code attempts to lock the same inode twice (double iolock/ilock), leading to a deadlock. The fix detects this corner case and handles it appropriately.
Original NVD description (English source)
In the Linux kernel, the following vulnerability has been resolved: drm/msm/dpu: fix mismatch between power and frequency During DPU runtime suspend, calling dev_pm_opp_set_rate(dev, 0) drops the MMCX rail to MIN_SVS while the core clock frequency remains at its original (highest) rate. When runtime resume re-enables the clock, this may result in a mismatch between the rail voltage and the clock rate. For example, in the DPU bind path, the sequence could be: cpu0: dev_sync_state -> rpmhpd_sync_state cpu1: dpu_kms_hw_init timeline 0 ------------------------------------------------> t After rpmhpd_sync_state, the voltage performance is no longer guaranteed to stay at the highest level. During dpu_kms_hw_init, calling dev_pm_opp_set_rate(dev, 0) drops the voltage, causing the MMCX rail to fall to MIN_SVS while the core clock is still at its maximum frequency. When the power is re-enabled, only the clock is enabled, leading to a situation where the MMCX rail is at MIN_SVS but the core clock is at its highest rate. In this state, the rail cannot sustain the clock rate, which may cause instability or system crash. Remove the call to dev_pm_opp_set_rate(dev, 0) from dpu_runtime_suspend to ensure the correct vote is restored when DPU resumes. Patchwork: https://patchwork.freedesktop.org/patch/710077/

