CVE-2026-52965
MediumCVSS 5.5Exploitation Probability (EPSS)
Low risk2th percentile - higher than 2% of all known CVEs
Summary
In the Linux kernel DRM TTM subsystem, a bug causes an infinite LRU walk when swapout fails. After ttm_tt_swapout() failure, restoring the resource's LRU position leads to the same resource being found again, resulting in an infinite loop.
Risk Assessment
An infinite loop can cause system hang or resource exhaustion, posing a risk to system stability and service availability in the organization.
Recommendation
Immediately update the Linux kernel to a version containing the fix (commit 52965). Monitor for patch availability and apply it as part of the standard patch management process.
Other vulnerabilities in Linux kernel
See all- CVE-2026-14367Low
A vulnerability in the I3C IBI subsystem of the Linux kernel (drivers/i3c/i3c_ibi_workq.c) stems from missing synchronization on the free-list of work nodes (sys_slist_t). Allocation and deallocation helpers are called from interrupt context (ISR) and the workqueue thread without locks, leading to a race condition. An attacker with physical access to the I3C bus can trigger a series of interrupts, causing list corruption, double allocation, or out-of-bounds writes.
- CVE-2026-80577Unknown
In the Linux kernel's drm/panthor driver, panthor_fw_load_section_entry() skips BO creation for zero-sized firmware sections but adds them to the section list, leading to NULL pointer dereference in later paths. The fix skips adding such sections to the list.
- CVE-2026-80571Unknown
In the Linux kernel powerpc/pseries papr-phy-attest, missing validation of cmd.length could lead to buffer overflow. The fix adds length checks and fixes memory leaks on error paths.
- CVE-2026-80567Unknown
In the Linux kernel Synaptics RMI4 driver (F54), worker errors were not propagated to the V4L2 queue, causing stale or uninitialized data to be delivered to userspace. The fix adds error checking and marks buffers as error state.
- CVE-2026-80566Unknown
In the Linux kernel, the hynitron_cstxxx driver improperly validated touch count and finger IDs. This can lead to corrupted touch state or out-of-bounds buffer access.
- CVE-2026-80564Unknown
In the Linux kernel, the gve driver lacks an implementation of adjfine, leading to a NULL pointer dereference when triggered from userspace, e.g., via testptp.
- CVE-2026-80563Unknown
A use-after-free vulnerability was found in the Linux kernel's gpio-sloppy-logic-analyzer driver. The 'trigger' debugfs file lacked proper protection, allowing a write to freed memory during device unbind. The issue was fixed by using debugfs_create_file() instead of debugfs_create_file_unsafe().
- CVE-2026-80543Unknown
In the Linux kernel, the xcrb_msg_to_type6cprb_msgx() and xcrb_msg_to_type6_ep11cprb_msgx() functions for s390/zcrypt copy a user space message into a kernel buffer based on length, but further processing assumes 4-byte alignment. As a result, up to 3 bytes of uninitialized kernel memory are forwarded to further processing, potentially exposing kernel memory to the crypto card firmware.
- CVE-2026-80542Unknown
In the Linux kernel, the amdgpu driver for AMD Display has a NULL pointer dereference in amdgpu_dm_crtc_set_vblank() when vblank is enabled or queried before a stream is attached to acrtc_state->stream. This can lead to a system crash.
- CVE-2026-80535Unknown
In the Linux kernel XFS filesystem, during directory tree repair, a self-referential directory may be detected. In such a case, the repair code attempts to lock the same inode twice (double iolock/ilock), leading to a deadlock. The fix detects this corner case and handles it appropriately.
Original NVD description (English source)
In the Linux kernel, the following vulnerability has been resolved: drm/ttm: Fix ttm_bo_swapout() infinite LRU walk on swapout failure When ttm_tt_swapout() fails, the current code calls ttm_resource_add_bulk_move() followed by ttm_resource_move_to_lru_tail() to restore the resource's bulk_move membership. However, ttm_resource_move_to_lru_tail() places the resource at the tail of the LRU list which, relative to the walk cursor's hitch node (placed immediately after the resource when it was yielded), puts the resource *in front of the* the hitch. The next list_for_each_entry_continue() from the hitch finds the same resource again, causing an infinite loop. Fix by deferring del_bulk_move to the success path only. On the success path, TTM_TT_FLAG_SWAPPED has just been set by ttm_tt_swapout() but the resource is still tracked in the bulk_move range, so ttm_resource_del_bulk_move()'s !ttm_resource_unevictable() guard would incorrectly skip the removal. Introduce ttm_resource_del_bulk_move_unevictable() which bypasses that guard.

