CVE-2026-46207
MediumCVSS 5.5Exploitation Probability (EPSS)
Low risk2th percentile - higher than 2% of all known CVEs
Summary
A vulnerability has been identified in the Linux kernel related to improper data copying for non-linear buffers. The issue was that during the copying of the original payload to a new buffer, the copy length was set to zero, resulting in no data being copied.
Risk Assessment
The lack of copied data to the monitoring interface may lead to improper functioning of applications using this interface, potentially affecting the stability and security of the system.
Recommendation
It is recommended to update the Linux kernel to the latest version to eliminate this vulnerability and ensure proper data copying for non-linear buffers.
Other vulnerabilities in Linux kernel
See all- CVE-2026-14367Low
A vulnerability in the I3C IBI subsystem of the Linux kernel (drivers/i3c/i3c_ibi_workq.c) stems from missing synchronization on the free-list of work nodes (sys_slist_t). Allocation and deallocation helpers are called from interrupt context (ISR) and the workqueue thread without locks, leading to a race condition. An attacker with physical access to the I3C bus can trigger a series of interrupts, causing list corruption, double allocation, or out-of-bounds writes.
- CVE-2026-80577Unknown
In the Linux kernel's drm/panthor driver, panthor_fw_load_section_entry() skips BO creation for zero-sized firmware sections but adds them to the section list, leading to NULL pointer dereference in later paths. The fix skips adding such sections to the list.
- CVE-2026-80571Unknown
In the Linux kernel powerpc/pseries papr-phy-attest, missing validation of cmd.length could lead to buffer overflow. The fix adds length checks and fixes memory leaks on error paths.
- CVE-2026-80567Unknown
In the Linux kernel Synaptics RMI4 driver (F54), worker errors were not propagated to the V4L2 queue, causing stale or uninitialized data to be delivered to userspace. The fix adds error checking and marks buffers as error state.
- CVE-2026-80566Unknown
In the Linux kernel, the hynitron_cstxxx driver improperly validated touch count and finger IDs. This can lead to corrupted touch state or out-of-bounds buffer access.
- CVE-2026-80564Unknown
In the Linux kernel, the gve driver lacks an implementation of adjfine, leading to a NULL pointer dereference when triggered from userspace, e.g., via testptp.
- CVE-2026-80563Unknown
A use-after-free vulnerability was found in the Linux kernel's gpio-sloppy-logic-analyzer driver. The 'trigger' debugfs file lacked proper protection, allowing a write to freed memory during device unbind. The issue was fixed by using debugfs_create_file() instead of debugfs_create_file_unsafe().
- CVE-2026-80543Unknown
In the Linux kernel, the xcrb_msg_to_type6cprb_msgx() and xcrb_msg_to_type6_ep11cprb_msgx() functions for s390/zcrypt copy a user space message into a kernel buffer based on length, but further processing assumes 4-byte alignment. As a result, up to 3 bytes of uninitialized kernel memory are forwarded to further processing, potentially exposing kernel memory to the crypto card firmware.
- CVE-2026-80542Unknown
In the Linux kernel, the amdgpu driver for AMD Display has a NULL pointer dereference in amdgpu_dm_crtc_set_vblank() when vblank is enabled or queried before a stream is attached to acrtc_state->stream. This can lead to a system crash.
- CVE-2026-80535Unknown
In the Linux kernel XFS filesystem, during directory tree repair, a self-referential directory may be detected. In such a case, the repair code attempts to lock the same inode twice (double iolock/ilock), leading to a deadlock. The fix detects this corner case and handles it appropriately.
Original NVD description (English source)
In the Linux kernel, the following vulnerability has been resolved: vsock/virtio: fix empty payload in tap skb for non-linear buffers For non-linear skbs, virtio_transport_build_skb() goes through virtio_transport_copy_nonlinear_skb() to copy the original payload in the new skb to be delivered to the vsockmon tap device. This manually initializes an iov_iter but does not set iov_iter.count. Since the iov_iter is zero-initialized, the copy length is zero and no payload is actually copied to the monitor interface, leaving data un-initialized. Fix this by removing the linear vs non-linear split and using skb_copy_datagram_iter() with iov_iter_kvec() for all cases, as vhost-vsock already does. This handles both linear and non-linear skbs, properly initializes the iov_iter, and removes the now unused virtio_transport_copy_nonlinear_skb(). While touching this code, let's also check the return value of skb_copy_datagram_iter(), even though it's unlikely to fail.