CVE-2026-23110
MediumCVSS 4.7Exploitation Probability (EPSS)
Low risk1th percentile - higher than 1% of all known CVEs
Summary
A race condition in the Linux kernel's SCSI layer can prevent the error handler from waking up when final commands complete concurrently. The issue stems from memory ordering problems and incorrect sequencing between counting busy commands and incrementing the failed counter. This can cause I/O on the SCSI host to become stuck in an error state.
Risk Assessment
The organization may experience a complete halt of I/O operations on SCSI devices, leading to data unavailability and potential loss of critical services. A local attacker could exploit this vulnerability to cause a denial of service (DoS) on the system.
Recommendation
Immediately update the Linux kernel to a version containing the fix, which adds a memory barrier on the error path and reorders calls in scsi_eh_inc_host_failed(). Upgrading to the latest stable kernel release is recommended.
Other vulnerabilities in Linux kernel
See all- CVE-2026-80577Unknown
In the Linux kernel's drm/panthor driver, panthor_fw_load_section_entry() skips BO creation for zero-sized firmware sections but adds them to the section list, leading to NULL pointer dereference in later paths. The fix skips adding such sections to the list.
- CVE-2026-80571Unknown
In the Linux kernel powerpc/pseries papr-phy-attest, missing validation of cmd.length could lead to buffer overflow. The fix adds length checks and fixes memory leaks on error paths.
- CVE-2026-80567Unknown
In the Linux kernel Synaptics RMI4 driver (F54), worker errors were not propagated to the V4L2 queue, causing stale or uninitialized data to be delivered to userspace. The fix adds error checking and marks buffers as error state.
- CVE-2026-80566Unknown
In the Linux kernel, the hynitron_cstxxx driver improperly validated touch count and finger IDs. This can lead to corrupted touch state or out-of-bounds buffer access.
- CVE-2026-80564Unknown
In the Linux kernel, the gve driver lacks an implementation of adjfine, leading to a NULL pointer dereference when triggered from userspace, e.g., via testptp.
- CVE-2026-80563Unknown
A use-after-free vulnerability was found in the Linux kernel's gpio-sloppy-logic-analyzer driver. The 'trigger' debugfs file lacked proper protection, allowing a write to freed memory during device unbind. The issue was fixed by using debugfs_create_file() instead of debugfs_create_file_unsafe().
- CVE-2026-80543Unknown
In the Linux kernel, the xcrb_msg_to_type6cprb_msgx() and xcrb_msg_to_type6_ep11cprb_msgx() functions for s390/zcrypt copy a user space message into a kernel buffer based on length, but further processing assumes 4-byte alignment. As a result, up to 3 bytes of uninitialized kernel memory are forwarded to further processing, potentially exposing kernel memory to the crypto card firmware.
- CVE-2026-80542Unknown
In the Linux kernel, the amdgpu driver for AMD Display has a NULL pointer dereference in amdgpu_dm_crtc_set_vblank() when vblank is enabled or queried before a stream is attached to acrtc_state->stream. This can lead to a system crash.
- CVE-2026-80535Unknown
In the Linux kernel XFS filesystem, during directory tree repair, a self-referential directory may be detected. In such a case, the repair code attempts to lock the same inode twice (double iolock/ilock), leading to a deadlock. The fix detects this corner case and handles it appropriately.
- CVE-2026-80533Unknown
In the Linux kernel XFS filesystem, during AGI repair, the function xrep_iunlink_walk_ondisk_bucket may attempt to use the pointer sc->sa.agi_bp, which can be null if the buffer verifier fails. The fix uses ragi->agi_bp instead, which skips verifier checks, to avoid walking off the end of memory.
Original NVD description (English source)
In the Linux kernel, the following vulnerability has been resolved: scsi: core: Wake up the error handler when final completions race against each other The fragile ordering between marking commands completed or failed so that the error handler only wakes when the last running command completes or times out has race conditions. These race conditions can cause the SCSI layer to fail to wake the error handler, leaving I/O through the SCSI host stuck as the error state cannot advance. First, there is an memory ordering issue within scsi_dec_host_busy(). The write which clears SCMD_STATE_INFLIGHT may be reordered with reads counting in scsi_host_busy(). While the local CPU will see its own write, reordering can allow other CPUs in scsi_dec_host_busy() or scsi_eh_inc_host_failed() to see a raised busy count, causing no CPU to see a host busy equal to the host_failed count. This race condition can be prevented with a memory barrier on the error path to force the write to be visible before counting host busy commands. Second, there is a general ordering issue with scsi_eh_inc_host_failed(). By counting busy commands before incrementing host_failed, it can race with a final command in scsi_dec_host_busy(), such that scsi_dec_host_busy() does not see host_failed incremented but scsi_eh_inc_host_failed() counts busy commands before SCMD_STATE_INFLIGHT is cleared by scsi_dec_host_busy(), resulting in neither waking the error handler task. This needs the call to scsi_host_busy() to be moved after host_failed is incremented to close the race condition.